Custom Mirror Mounts

mounted

The Problem.

Caterham’s mirrors are terrible. Seriously. They’re enormous and because they’re not convex, you can’t see anything. The original Eccles mounts are only attached at the hinge so are prone to shaking.

My solution

My mounts take Spa or Motamec convex mirrors, which means you can change lane without just guessing if you’re going to die.

The mounts use the same hinge design as the Eccles mounts, but with the third bolt, which hooks into the previously drilled hole that your standard Caterham mirrors mounted into. This creates much, much more stiffness than the original mounts and stops the vibration of the mirror.

There is also an access hole so that you can access the tightening screw for the Spa mirrors.

As all holes drilled for Caterham mirrors are different, all the mounts need to be unique. Left side, right side, both different and custom.

How do they compare to my cheaper caterham adapters?

These adapters are half the price and no measuring needed! The custom ones are a little stiffer as they’re braced in 2 dimensions, but there’s not a lot in it.

How much are they?

£66 including delivery, but you pay me after you’re happy. I’ll make them, send them out, fix any problems, and then you pay.

Are they any good?

I’ve been running them for a few months now and have done >2000 miles including 3 track days and no problems. I’ve sold a few and everyone has paid!

Video here from the Karussell. if that doesn’t make your mirrors shake nothing will. click on it:

ROCK SOLID

What do they look like?

These are 3D printed, so they typically look like this: Both

Are they strong enough?

Yes. They’re much stronger than you’d think. I’ve snapped one, but it took a bench vice and a hammer. They look like this inside: Honeycomb

The front side has a pattern from the printing which you can make out in bright light, the back side is dull.

How do I order?

The instructions are in the form.
–>use this form to order<– I’ll post them out. If you’re happy, you send me the money, If you’re not, you return them.

What comes in the kit?

  • 2x custom mounts
  • 4x 25mm M5 countersunk bolts for the hinge attachment
  • 2x 25mm M5 countersunk bolts for the bottom attachment
  • 2x 14mm M5 countersunk bolts for the mount-mirror bolt

What do I need?

  • 2x Spa/Motomec/CBS mirrors (buy the convex spa ones here or here or the motamecs here (note that https://www.kitcardirect.co.uk/spa-style-formula-f1-wing-mirror-carbon-pair.html seem to be motamecs)

  • 2x Side screens that have been drilled.
  • 2x original Caterham brass door hinge pivots (just gently tap them out of the existing pivots by the pointy end. The end that is inserted is knurled, or you can get them here or here)
  • 8x original nyloc nuts and washers from hinge and mirrors.

How do I fit them?

  • Open 1 beer (Your choice. My preference is something hoppy like a Siren or a Landlord)
  • test fit mounts, just drop the bolts through and check it all lines up. if a mistake has been made, this is the time to find out.
  • unscrew lower hinge from screen.
  • tap out brass hinge pivot (it’s knurled on the end that is inserted) by putting the hole above a gap in a vice or on the edge of a bench and tapping it out by the pointy end.
  • take brass hinge pivot and tap it into your new mount. it goes in smooth, pointy end first and should grip onto the knurled end.
  • don’t tap it in upside down!
  • With the screws inserted, offer up the Spa mirror to the car and set the angle of the mirror correct.
  • once mirror is perfect, tighten the spa mirror down hard and the bolt mount to side screen with your nyloc nuts.
  • enjoy worrying that now your rear-view mirror vibrates more than your wing mirrors.
  • enjoy ignoring everything behind you anyway.

Back

Do you do different colours from black?

Yes! for £5 more I can do a colour that I have filament for (currently Orange, Red, Green, Grey, Blue). I can do others but cost will be more. I’m not guaranteeing colour tone.

Can I use either Motamec or Spa mirrors

Yes, although I personally think the Spa mirrors are better as they’re more convex and a little stiffer (comparison here). they are a bit more finicky to fit and adjust though. you’ll need to countersink the bolt holes on your motamec mounts for the bolts to be the right length.

What if you think they’re rubbish?

cut them in half with a saw, send me a photo them, I’ll not ask you for any money.

Delivery:

Usually delivery is within a week, sometimes it is a little more, sometimes it’s next day. If you need it rushing, please get in touch. International delivery is usually about £15 to the US, Japan or Oz, around £9 to France, etc.

Colours:

I have many colours available in PLA. In PETG generally only black and grey. not all products are available in PLA as it is not stable under high temperature. if you have a special request, just ask as I may be able to help.

Surface Finish:

These are 3D printed parts and for some of them the finish of the outward facing side can be either carbon-fibre effect, triangles, textured or plain as seen here: Surface Finish I make it carbon by default. If you want something else, please let me know.

Contact:

to contact me, either email john@uberniche.co.uk or hit me up on Instagram